Interference between light waves is the reason that thin films, such as soap bubbles, show colorful patterns. If the grating spacing (d, the distance between slits) is known and careful measurements are made of the angles at which light of a particular color occurs in the interference pattern, the wavelength of the light can be calculated. For a diffraction grating, then, with a large number of slits, the pattern is sharp because of all the destructive interference taking place between the bright peaks where constructive interference takes place.ĭiffraction gratings, like prisms, disperse white light into individual colors. Completely constructive interference, however, takes place only when the path lengths differ by an integral number of wavelengths. For 4 slits, there are three places, for 5 slits there are four places, etc. One is located at the point where the path lengths differ by 1/3 of a wavelength, while the other is at the place where the path lengths differ by 2/3 of a wavelength. For three slits, however, there are two places where destructive interference takes place. Between the central peak (m = 0) and the next one (m = 1), there is a place where one wave travels 1/2 a wavelength further than the other, and that's where destructive interference takes place. Why is the pattern much sharper? In the double slit, between each peak of constructive interference is a single location where destructive interference takes place. The positions of the peaks, which come from the constructive interference between light coming from each slit, are found at the same angles as the peaks for the double slit only the sharpness is affected. With a large number of slits, the peaks are very sharp. As more slits are added, the peaks in the pattern become sharper and narrower. With a double slit, the interference pattern is made up of wide peaks where constructive interference takes place. The name is a bit misleading, because the structure in the pattern observed is dominated by interference effects. We've talked about what happens when light encounters a single slit (diffraction) and what happens when light hits a double slit (interference) what happens when light encounters an entire array of identical, equally-spaced slits? Such an array is known as a diffraction grating. Generally what you see is a fringe pattern that has missing interference fringes these fall at places where dark fringes occur in the diffraction pattern. If W is much larger than d, the pattern will be dominated by interference effects if W and d are about the same size the two effects will contribute equally to the fringe pattern. The shape of the diffraction pattern is determined by the width (W) of the slits, while the shape of the interference pattern is determined by d, the distance between the slits. Essentially, this is because each slit emits a diffraction pattern, and the diffraction patterns interfere with each other. Note that diffraction can be observed in a double-slit interference pattern. The bright fringes fall between the dark ones, with the central bright fringe being twice as wide, and considerably brighter, than the rest. The argument can be extended to show that : The rays are half a wavelength out of phase because of the extra path length traveled by one ray in this case that extra distance is : In other words, the light from one half of the opening cancels out the light from the other half. These two rays would interfere destructively, as would rays 2 and 6, 3 and 7, and 4 and 8. In the diagram above, let's say that the light leaving the edge of the slit (ray 1) arrives at the screen half a wavelength out of phase with the light leaving the middle of the slit (ray 5). To see why this is, consider the diagram below, showing light going away from the slit in one particular direction. A big difference between the single and double slits, however, is that the equation that gives the bright fringes for the double slit gives dark fringes for the single slit. For the single slit, each part of the slit can be thought of as an emitter of waves, and all these waves interfere to produce the interference pattern we call the diffraction pattern.Īfter we do the analysis, we'll find that the equation that gives the angles at which fringes appear for a single slit is very similar to the one for the double slit, one obvious difference being that the slit width (W) is used in place of d, the distance between slits. With the double slit, each slit acted as an emitter of waves, and these waves interfered with each other. The analysis of the resulting diffraction pattern from a single slit is similar to what we did for the double slit. We discussed diffraction in PY105 when we talked about sound waves diffraction is the bending of waves that occurs when a wave passes through a single narrow opening.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |